Powder Filling Production Line
A leaking tube tail can result from an unsuitable tube structure, product on the seal area or an unstable sealing cycle. Increasing sealing energy without identifying the cause can distort the tube while leaving the original problem unresolved.
When evaluating a tube filling and sealing machine, test the filled tube and its sealing method as a complete package.
Where sealing fits in the machine cycle
An automatic tube machine typically loads and locates the tube, orients the printed mark where required, dispenses product, seals the open tail, applies the specified coding or trimming operation and discharges the finished tube.
Several stations may act during the same indexing cycle. Stable tube location therefore matters beyond the filling nozzle: the tube must arrive at the sealing station at the correct height and orientation.
The supplied product material includes ultrasonic sealing. Confirm the actual configuration offered, since other machines may use hot-air sealing or a different method.
Match the sealing method to the tube
Plastic and laminate tubes can have different layer structures and thicknesses. The seal must join the intended sealable layer under conditions appropriate to that construction. An all-aluminium tube normally requires a different closure arrangement, so it should not be treated as a direct substitute in a plastic-tube sealing trial.
Ultrasonic and thermal methods create the joint in different ways. Neither method should be described as universally leakproof or superior for every tube. Compatibility must be established with actual samples, including the product inside.
Inspect the seal area before adjusting the process
Product dragged onto the open tail can prevent a consistent joint. Look for nozzle drips, stringing, splash and product carried up the tube wall during filling.
Fill level matters because adequate space must remain for tail handling and sealing. A larger nominal tube may still need a defined unfilled section. Ask the tube supplier and machine supplier to agree on the working fill and sealing-zone dimensions.
| Leak pattern | Checks to prioritize |
|---|---|
| Weak joint across most of the tail | Tube compatibility and the defined sealing settings |
| One side seals and the other side leaks | Tube position, jaw alignment and uneven contact |
| Intermittent channels through the seal | Product contamination, folds or inconsistent tube presentation |
| Burned, thin or badly distorted tail | Excessive treatment or an unsuitable process window |
| Good empty-tube seal, poor filled-tube result | Filling behaviour, headspace and product interaction |
Inspect adjustments under the machine's approved procedure. The appropriate corrective action depends on the installed sealing system.
Validate a process window
A useful trial examines more than one convenient setting. The objective is a repeatable range that produces acceptable seals with normal variations in tube supply, fill condition and production speed.
For a thermal process, relevant variables can include temperature, time, pressure and cooling. For ultrasonic sealing, energy delivery, tooling contact and pressure must match the system. Use the manufacturer's defined parameters rather than transferring settings from a different machine.
Record the tube batch and product condition with every test. Changing the tube supplier and sealing settings simultaneously makes it hard to explain an improvement or a failure.
Test the packaged product
Agree on an appropriate leak and seal-strength assessment with the packaging specification. Examine samples after any required conditioning, since a joint can behave differently immediately after sealing and later during handling.
Include start-up samples, normal production and samples after a planned stop. Repeated stopping can expose unstable filling or sealing conditions that a brief uninterrupted demonstration misses.
Which samples should a buyer send?
Provide actual tubes, their material specification, caps where relevant and the intended product. Include tube diameter and length, fill quantity, acceptable tail appearance and the required coding. Product viscosity at filling temperature is more useful than a description such as thick cream.
Trace failures back to the packaging lot
Label failed and accepted tubes with the tube lot, product lot, machine setup and approximate production time. Compare whether the defect follows a particular shipment or occurs across all supplied tubes.
A tube's overall dimensions do not fully describe its sealing behaviour. Ask for the packaging construction and the tolerances relevant to the sealing area. If an alternative tube supplier is planned, include that supplier's material in the trial rather than assuming a successful test transfers automatically.
Keep unused tubes and filled examples from the same lot. Empty-tube tests can help examine the sealing arrangement, while filled examples reveal interactions with product and filling. Neither test alone represents every part of the packaging duty.
Compare the first accepted seal with later production
Observe samples through a representative operating period and after a planned stop. Record whether failures appear at start-up, after tooling becomes established in operation or when the machine resumes.
Also note any change in product temperature or consistency while it waits for filling. A nozzle that dispenses cleanly at the beginning of a run may begin to string or drip as the product changes condition. This can affect the sealing zone even if the sealing station itself has not changed.
Collect samples by time and failure type. A single reject percentage can hide a repeating event, such as a short period of contamination after each refill or restart.
Assess seal integrity and package appearance separately
A straight, neatly trimmed tail is useful for appearance, but it does not establish integrity. Conversely, a package that passes an appropriate leak test may still fail an agreed visual or coding requirement.
Write separate acceptance criteria for joint performance, tail appearance, coding and fill quantity. State the sample-conditioning and test method for each requirement. Where the buyer has an established packaging specification, use that as the common basis for the machine and tube suppliers.
If transport or later handling exposes the joint to a particular load, include that condition in the packaging assessment. The machine supplier should know what the completed package must withstand, rather than being asked to guarantee an undefined strong seal.
Follow the product residue back to filling
When product appears in a failed joint, compare the tube immediately after dosing with the same tube after indexing to the sealing position. This helps identify whether contamination occurs during nozzle withdrawal, product settling or tube movement.
Inspect whether a strand of product follows the nozzle and whether the tube remains supported at the intended height. Ask the supplier to evaluate the actual nozzle and product condition. A general anti-drip claim does not establish that a specific cream or gel will leave the tail clean at every intended speed.
Keep the target fill and unfilled sealing area explicit in the test record. Overfilling should not be used to meet an appearance target if it compromises the required tail geometry.
Include a format change in the purchasing assessment
The liquid-packaging route guide places tube filling alongside other package formats. Within the tube route, changing diameter, length or construction may require holders, guides or sealing tooling as well as a controller setting.
Demonstrate the change from one principal format to another using production materials. Record the time until accepted filled and sealed tubes are produced, including trial pieces and adjustment. Identify the parts included in the quote and those needed for future formats.
Make the supplier's trial report usable afterward
Request the tube specification, product condition, filling quantity, production rate and sealing configuration used for the accepted samples. Include rejection reasons and the agreed verification results.
That report gives the plant a reference when a later tube lot or product change creates leakage. Without it, operators may be forced to search for a new setting without knowing whether the original packaging material, filling behaviour or sealing condition has changed.
The [tube filling and sealing machine page](/product/tube-filling-sealing-machine/) describes the current machine arrangement. To investigate leaks or arrange a trial, [send tube samples, the fill specification and close-up photos of the failed tail](/contact/). State whether leaks occur immediately, after squeezing or after storage and transport.
Related guides
Related Products
Sizing equipment for your line?
Send the product, the batch size and the utilities you have. We reply with the model, the cycle time and what the cooling side needs.


