Company News

Why We Built a Technical Resource Hub for Dairy Processors

Most equipment questions arrive before a quotation does. Here is what we publish in this section, who writes it, and how to use the guides when comparing dairy lines.

Published

4 November 2026

Read time

5 min read

Inside

7 sections, in reading order

Questions

Send the product and the batch size, we answer with figures.

Most messages that reach us do not start with a price question. They start with a number: how much can this machine put out in a day, and will it fit the milk I can actually collect.

That question cannot be answered from a quotation sheet. A 200 L pasteuriser with a good cooling supply and a tight batch rhythm is a different machine from the same tank running on 22 °C mains water with one operator doing everything by hand. Same model number, different daily output.

So we started writing the missing part down.

What kept coming up in the inbox

A few themes repeat often enough that answering them one email at a time stopped making sense.

  • Capacity quoted as tank volume, while the buyer plans around finished packs per shift.
  • Cooling treated as a detail, when it usually sets the cycle time.
  • Cleaning described as something that happens after production, not as part of the schedule.
  • Machines bought one at a time, then found to be mismatched when the line is assembled.

None of these are sales problems. They are process questions, and they come up before anyone is ready to talk about a purchase order.

What we publish here

The section is split into four parts, and the split follows the way a project actually moves.

  • Resources holds the technical guides: how a stage works, what controls it, where it drifts, how to size it. This is the largest part and it will keep growing.
  • Company News covers the workshop side: what changed in the range, what we are building, what came back from a commissioning trip.
  • FAQs collects the questions that arrive before a quotation: utilities, cleaning, materials, lead time, installation.
  • Solutions looks at whole lines rather than single machines, from reception through to packed product.

Who writes it

The guides are written by the people who size the equipment and stand next to it during commissioning. That has two consequences.

First, the writing is concrete. A guide about homogeniser pressure talks about the pressure at the valve, not the number printed on the nameplate, because that is the difference that shows up on the shop floor.

Second, we leave gaps where we do not know. If a question depends on local regulation, on a utility we have not seen, or on a product we have not run, the article says so instead of inventing an answer.

Between us, more time goes into questions than into copy. A guide usually starts as an answer to one buyer, and gets written down properly the second time the same question arrives.

What we deliberately do not do

There are three things you will not find in this section.

We do not publish customer names, plant photos or order values without written permission. Case material appears only where the customer has agreed to it, and even then it is checked line by line before it goes up.

We do not publish performance figures we have not measured or seen measured. Where an article uses a worked example, the numbers are labelled as illustrations of the arithmetic, not as a promise for a particular machine.

We do not pretend a batch tank is a continuous system. A jacketed vessel with a temperature controller is not a UHT plant, and calling it one would only create a problem later, usually during an inspection.

How the guides get updated

An article is not finished when it is published. Two things push it back into editing: a question from a buyer that the text does not answer, and a commissioning job that shows the advice was incomplete.

When that happens we revise the article instead of publishing a second one on the same subject. Two thin pages competing for the same phrase help nobody, and whoever lands on the older one gets the worse answer.

Where a guide describes a calculation, the formula stays visible so you can rerun it with your own figures. Where it describes a setting, the article names the parameter you would look for on the controller rather than a fixed value, because the value depends on the product.

How to use the guides

Read the process first, then the numbers, then the price. The order matters.

If you are planning a small dairy, start with the workflow guide for your product family. It sets the sequence and shows where the buffers sit. From there, the individual guides cover the stage you are unsure about: fermentation tank sizing, whey drainage, fill volume drift, tail seal leaks.

Bring the constraints you already know. Daily volume, available power, water temperature, labour, the pack format you want to sell. With those four, most of the sizing work is arithmetic rather than guesswork.

If a guide raises a question it does not answer, send it to us. We add the answer to the article when it is a question more than one buyer is likely to ask.

What this section is not

It is not a service manual. Operating procedures, safety interlocks and cleaning validation belong to the documentation that ships with the machine and to the regulations where you operate.

It is also not a substitute for a site survey. A line that looks straightforward on paper can turn on the position of a floor drain or the height of a door.

Used the right way, though, it should shorten the distance between the question you have today and the specification you can sign off on. That is the whole point of putting it here.

Sizing equipment for your line?

Send the product, the batch size and the utilities you have. We reply with the model, the cycle time and what the cooling side needs.

WhatsApp Email
Process first, machine second — pick the product you make. All applications ›
Dairy processing tanks and plate heat exchangers installed in a production hall
Bottling line installed in a factory hall, bottles moving through the filler

Turnkey Production Lines

A complete line is more than a row of machines. We size the filler, the sealing station and the conveyor runs against your product, pack format and shift target, then deliver it as one commissioned unit.

Complete powder filling line running in a factory hall