Resources

High Shear Homogenizer

At a Glance Item Detail Core spec 50-500 L, 2.2-7.5 kW What sets it apart Lift-type rotor in a mobile drum; dispersing disc matched to the product Pain point solved A large tank is…

Published

29 October 2026

Read time

10 min read

Inside

8 sections, in reading order

Questions

Send the product and the batch size, we answer with figures.

At a Glance

Item Detail
Core spec 50-500 L, 2.2-7.5 kW
What sets it apart Lift-type rotor in a mobile drum; dispersing disc matched to the product
Pain point solved A large tank is overkill and a hand mixer cannot reach fineness

A 50-500 L lift-type high-shear disperser at 2.2-7.5 kW, covering trial batches and mid-volume runs without changing vessels.

Where a High Shear Homogenizer Earns Back Its Cost

A development lab and a production line often share one workshop. A new formula needs a five-litre trial batch to check stability; volume production then asks for several hundred litres per shift. A line like this cannot justify a several-thousand-litre tank, and a hand stirrer cannot reach the required fineness. The machine in between is this high shear homogenizer.

The working pattern is direct. A covered vessel holds the material and rolls under the machine. A clamping device locks it in place, the dispersing head travels down its lifting track into the liquid, and a high-speed disk shears, disperses and homogenizes the batch in one run. When the cycle ends the head rises, the vessel rolls away and the next one rolls in, with almost no dead time between batches.

The unit covers five ratings from 50 to 500 L with motors from 2.2 to 7.5 kW. The spindle runs at 2880 r/min with inverter control, the lifting stroke covers 400 to 600 mm, and electric or pneumatic lifting is available. An optional heating belt wraps the vessel for 0 to 100 °C temperature control. Cosmetics lotion, paint and ink, adhesives and resins, and dairy blending all fall inside its duty range.

High Shear Homogenizer Models, Rotor Speed and Motor Ratings

Emulsion homogenizer structure diagram

Five-rating comparison (per the official parameter table)

Item 50 L 100 L 200 L 300 L 500 L
Charge volume 50 L 100 L 200 L 300 L 500 L
Motor power 2.2 kW 3 kW 4 kW 5.5 kW 7.5 kW
Dimensions 800×900×2150 mm 800×900×2150 mm 800×900×2150 mm 970×1240×2500 mm 1100×1420×2550 mm
Machine weight 130 kg 136 kg 150 kg 220 kg 280 kg
Packing size 900×1000×2350 mm 900×1000×2350 mm 900×1000×2350 mm 1070×1340×2700 mm 1200×1520×2750 mm
Packing weight 145 kg 156 kg 170 kg 240 kg 300 kg

General parameters

Item Specification
Model Quoted per order
Voltage 380 V / 50 Hz
Spindle speed 2880 r/min, inverter controlled
Lifting method Electric / pneumatic
Lifting stroke 400 to 600 mm
Heating Vessel heating belt, 0 to 100 °C
Material Stainless steel product-contact parts (specific grade quoted with the offer)
Certification ISO 9001, ISO 14001, ISO 45001, CE, BSCI, ETL
OEM / ODM Accepted
Core component warranty 1 year

Working Principle of a High Shear Homogenizer

In short. Material goes into a covered vessel and rolls into position, where the clamp locks it. The dispersing head travels down the lifting track until the disk sits below the surface. The motor spins the disk at high speed; material is drawn into the disk center, flung across the toothed edge and refined by intense shear. When fineness is reached, the head rises, the vessel rolls out, and the material moves to the next station.

01
Charging and fixing
Material is poured into the covered vessel, whose lid stays partly open for observation and topping up. The vessel rolls under the machine and the clamping device locks the body from both sides so it cannot shake or drift at high speed. The machine needs no fixed tank: changing product means changing the vessel.
02
Head down
The operator presses the lift switch and the head descends 400 to 600 mm along the lifting track until the disk sits at working depth. Depth drives circulation; the common band is from just submerged to half submerged, adjusted to viscosity.
03
High-shear dispersing
A copper-winding motor drives the disk through the stirring shaft at a rated 2880 r/min, with stepless speed control from the inverter. Material is drawn into the disk center, accelerates across the face and jets off the toothed edge, hitting the vessel wall and the liquid surface. Droplets and particles are refined by shear and turbulence. Where the process needs heat, the vessel heating belt holds the set temperature.
04
Discharge and batch change
When dispersing is done, the head rises, the clamp releases, and the vessel rolls straight to filling or holding, or tips into the next station. The lid keeps dust and foreign matter out during transfer.

Emulsion homogenizer applications in cream, lotion, sauce and juice

Product Performance Advantages

  1. A high-shear head with batch fineness under control. A rated 2880 r/min spindle and toothed disk deliver the tip speed needed for a stable emulsion, and inverter speed lets one machine cover pre-mixing through fine dispersing at different shear levels.
  2. Vessel-type structure: changing product means changing the vessel. Without a fixed tank to clean, color changes in cosmetics or paint trials mean swapping the whole vessel. Cross-contamination risk stays low and batch gaps stay short.
  3. Customizable disk and paddle. Disk form and paddle type follow the viscosity and target fineness. Low-viscosity lotion and high-viscosity paste use different disk profiles, and this level of customization does not carry tooling-scale cost.
  4. Electric or pneumatic lifting. Electric lifting runs on mains power alone; pneumatic lifting is fast and holds position well, and gets the nod when the workshop has a compressed air supply.
  5. Optional heating from 0 to 100 °C. The vessel heating belt covers temperature-controlled processes such as resin pre-polymerization and paste melting, while routine ambient dispersing is unaffected.
  6. Small footprint for lines and labs alike. The 50 L rating stands only 800×900×2150 mm, fitting a lab corner or a slot beside the production line.

Engineering Design

Dispersing disk and clamping device of an emulsion homogenizer

Lifting system. A lifting track and switch form the frame, with a 400 to 600 mm stroke. The electric option drives directly from the motor; the pneumatic option runs on compressed air. Choose by the workshop’s utility conditions.

Drive system. A copper-winding motor with inverter, rated at 2880 r/min. Copper windings carry a better temperature margin through long shifts, and the inverter adds soft starting, protecting the disk from shock torque on high-viscosity loads.

Dispersing system. The stirring shaft ends in the dispersing disk, and the tooth profile at the edge sets shear intensity. The source data notes the disk can be customized per customer requirements: multi-layer toothed disks for thick paste, standard disks for thin lotion.

Fixing system. The clamping device grips the vessel body. Dispersing viscous material loads the vessel hard, and clamp lock-down decides how steadily the machine runs.

Structure breakdown

No. Part Function
1 Mixing tank with cover Holds the material; covered transfer keeps foreign matter out
2 Lifting track Guides head travel, 400-600 mm stroke
3 Motor Copper-winding motor driving the stirring shaft
4 Stirring shaft Transmits torque to the dispersing disk
5 Disperse disk High-speed shear at the toothed edge; customizable
6 Lift switch Controls head up and down
7 Control box and VFD Speed control, start and stop, overload protection
8 Clamping device Locks the vessel against shaking during dispersing

Emulsion homogenizer operation steps

Operating Procedure

  1. Charging. Pour material into the covered vessel and roll it under the machine.
  2. Fix and lower. Lock the clamp and press the lift switch to bring the head to working depth.
  3. Set and start. Set speed and heating temperature per the process card, start dispersing, and watch through the lid opening.
  4. Sample check. Stop at time, sample for fineness or flow, and extend the cycle if the spec is not met.
  5. Raise and discharge. Return the head to the top position, release the clamp, and roll the vessel to the next station.
  6. Cleaning. Clean disk and vessel wall before changing product; same-category continuous runs clean per shift.

Where a High Shear Homogenizer Is Used

Cosmetics and daily chemical sampling and small batches. Lotion, cream and shower gel in small production runs and formula trials. The vessel structure changes product fast, and one machine covers the transition from R&D to volume production.

Paint, ink, pigment and dye. These materials live and die by fineness and uniformity, and the disk’s shear decides color consistency from batch to batch. It is the most traditional territory for dispersing machines.

Resin, adhesive and emulsion polymerization. Dispersing and pre-emulsification of medium to high-viscosity material, with the heating belt holding temperature so melting and dispersing finish in one vessel.

Dairy and beverage blending. Small and mid-batch blending of milk bases and protein drinks, with lower cleaning pressure than fixed-tank machines between batches.

Customization

Disk form and paddle type are customized to the material; lifting is electric or pneumatic; heating is optional per process; body material, surface finish and panel language follow OEM and ODM orders. Customer logo printing is supported. Tooling is quoted with the offer.

Commercial Information

Item Details
Minimum order quantity (MOQ) 1 set
Lead time quoted with the offer (stock machines and custom machines differ; per quotation)
Packing Waterproof membrane inner wrap plus standard wooden case outer packing, suited to ocean freight
Trade terms Quoted per order
Port of shipment Main ports in China (commonly Qingdao, Shanghai, Ningbo, Tianjin, Guangzhou); specific port per quotation

Quality Inspection and After-Sales

Pre-shipment video inspection and a mechanical test report are provided, with an English manual shipped alongside. The core component (motor) carries a one-year warranty with online technical support. Faults are diagnosed remotely first; on-site repair is arranged when needed, and overseas projects can include an engineer for installation and operator training. The source data lists no separate wear-parts schedule; inspect the disk and bearings by duty intensity and cover common parts in the first order.

Choosing the Right High Shear Homogenizer

  1. Size the rating by the largest single batch. Five ratings run from 50 to 500 L. A common practice is to choose at about eighty percent of the routine maximum batch, leaving surface for foam and vortex.
  2. Size power and disk by viscosity. Thin lotion is served by 2.2 to 4 kW; high-viscosity paste wants 5.5 kW or more with a multi-layer toothed disk. Do not run a small motor at heavy load.
  3. Size lifting by utilities. Choose pneumatic with a stable air supply and electric without one; processing capacity is the same either way.
  4. Size heating by process. Processes that need melting or temperature holding take the heating belt option; routine ambient dispersing need not pay for it.

High Shear Homogenizer Questions Buyers Ask

1. Is this machine batch or continuous?

Batch. One vessel runs at a time and the next rolls in after it. It suits many varieties in small volumes. For continuous, high-volume, low-viscosity homogenizing, look at the high-pressure homogenizer; for large-volume high-viscosity emulsifying, look at the vacuum emulsifying tank.

2. Does pneumatic lifting need an air compressor?

The pneumatic option runs on compressed air. If the workshop has no air supply, a compressor is needed; share your utility conditions at selection stage.

3. How fine can the emulsion get?

Fineness depends on disk type, speed and cycle time. The standard configuration meets routine lotion and paint requirements; for special targets, send a sample for a trial run and confirm with data.

4. Is the vessel included?

The vessel is a configured accessory matched to the rating, with cover included. Custom vessels or a head-only configuration are confirmed per quotation.

5. What is the MOQ?

One set. Pricing for volume orders is negotiated separately.

6. Can our logo go on the machine?

Yes. Logo printing and panel language are configured per OEM order.

7. How is export installation arranged?

Overseas installation is available, with an engineer on site for setup and free operator training. Routine faults are diagnosed remotely first, with on-site service when needed.

8. How is this different from the large vacuum emulsifying mixer and the high-pressure homogenizer?

This unit is a high-shear head over a movable vessel, batch sizes of 50 to 500 L, for medium to high-viscosity material. The large vacuum emulsifying mixer is a fixed tank taking 300 to 5000 L per batch with vacuum and jacket. The high-pressure homogenizer is a continuous in-line unit at the 20 MPa class for low-viscosity liquids such as milk and juice. Each has its own territory.

What Happens Next With a High Shear Homogenizer Enquiry

Send over your material type, single batch volume, viscosity range and target fineness, and we will propose a power rating, disk type and lifting method. If fineness is the worry, send a sample for a trial run and let the data speak.

Contact

Henan Gondor Machine Co., Ltd. Website inquiry form, WhatsApp or email. Replies within 24 hours on working days.

Related Equipment

Get High Shear Homogenizer Pricing

Send us the daily volume, the product and the container or pack format you are working with, and we will come back with a model recommendation, a utility list and a price.

Get an instant quote from our most experienced consultants.

Related guides

Sizing equipment for your line?

Send the product, the batch size and the utilities you have. We reply with the model, the cycle time and what the cooling side needs.

WhatsApp Email
Process first, machine second — pick the product you make. All applications ›
Dairy processing tanks and plate heat exchangers installed in a production hall
Bottling line installed in a factory hall, bottles moving through the filler

Turnkey Production Lines

A complete line is more than a row of machines. We size the filler, the sealing station and the conveyor runs against your product, pack format and shift target, then deliver it as one commissioned unit.

Complete powder filling line running in a factory hall